Peli 1510 Protector Carry On Case with Foam, Black, IP67 Watertight, Wheeled

In this bundle 1 × Peli 1510 Protector Case, Black (No Foam) 1 × Peli Full 1510 Foam Set - 4 Piece Replacement (1511) Peli 1510 Protector Case: Black (No Foam) The 1510 is the case you see coming off every touring flight case trolley and out of every camera department, Peli built it to the maximum airline carry-on size, so a radio mic rack, a camera body and lenses, or a laptop and interface travels in the cabin with you rather than in the hold. Watertight to IP67, rated from −40 °C to +87.8 °C, and certified to DEF STAN 81-41. In this bundle it comes with the full four-piece Peli foam set. 5.44 kg Empty weight IP67 Ingress rating Cabin size Carry-on design Lifetime Peli guarantee Cabin baggage, check your carrierPeli designs the 1510 to the maximum airline carry-on size, but cabin baggage allowances vary by airline and by aircraft. Confirm your carrier's exact dimensions and weight limit before you travel, particularly on regional turboprop and single-aisle short-haul routes, where hold-stowage is common regardless of case size. Foam set includedThe case is the no-foam version; this bundle adds the matching four-piece foam set (Peli 1511, part 1510-400-000), which drops straight in. TrekPak and padded divider sets also fit. Features Built to maximum airline carry-on size Double-throw latches O-ring seal with automatic pressure equalisation valve Two wheels and retractable extending handle Stainless steel padlock protectors, 8 mm padlock hole Moulded nameplate for asset marking DEF STAN 81-41 certified; MIL-STD-810G fungus tested 29.1 kg buoyancy Specifications Interior dimensions 502 × 279 × 193 mm (L × W × D) Exterior dimensions 559 × 351 × 229 mm (L × W × D) Lid / base depth 45 mm / 147 mm Interior volume 0.027 m³ Weight (empty) 5.44 kg Buoyancy 29.1 kg Ingress protection IP67, watertight to 1 m for 30 minutes Certification DEF STAN 81-41; MIL-STD-810G (fungus) Temperature range −40 °C to +87.8 °C Body material Polypropylene Latch / pin material ABS / stainless steel Colour Black Warranty Peli Limited Lifetime Guarantee Peli Full 1510 Foam Set - 4 Piece Replacement (1511) The full four-piece replacement foam set for the Peli 1510 Protector Case, Peli's own part 1510-400-000, catalogued globally as the 1511. Two layers of pre-scored Pick N Pluck base foam let you tear a bespoke cavity for your kit in a few minutes without a knife or a CNC quote, while the convoluted lid foam holds everything down against the closed lid. The correct replacement when the original foam in a working case has compressed, absorbed moisture, or been plucked for a job you no longer run. 4 pieces Complete set Pick N Pluck Pre-scored base 1510 / 1510M Fits Foam is not covered by the case guaranteePeli's Limited Lifetime Guarantee applies to the case itself, it expressly excludes contents and foam. Foam is a wear item; plan on replacing it periodically in hire stock and heavy touring use. Plucking guidancePeli recommend leaving at least 25 mm of foam between your equipment and the case wall. Lay the kit on the foam, mark the outline, and pluck one square at a time: you cannot put the squares back. Features Genuine Peli foam, cut to the exact 1510 interior Two Pick N Pluck layers, pre-scored in 19 × 13 mm squares Convoluted lid foam retains contents against the lid Solid base layer protects the case floor No tools required to configure Also fits the 1510M Protector Mobility Case Specifications Peli part number 1510-400-000 (catalogued as 1511) Set contents 4 pieces, see breakdown below Lid foam 1 × convoluted, 46 mm Base foam 1 × solid, 13 mm Pick N Pluck layers 2 × 67 mm, pre-scored Material Polyurethane Compatibility Peli 1510 Protector Case; Peli 1510M Protector Mobility CaseShow more

from £299.00

1 offer

See all offers